Product Description:
Hawks Motorsports is pleased to offer our clients the following.
This complete air-box mounting-hardware and air-lid clip kit is designed for compatible 1998-2002 Chevrolet Camaro and Pontiac Firebird models equipped with a factory-style LS1 V8 air-intake assembly.
The kit combines four titanium lower air-box mounting bolts with a silver finish and two chrome air-lid fastener clips. Together, these components secure the lower air box to the vehicle and retain the front of the air-filter lid in its installed position.
Original fasteners are frequently missing, mismatched, corroded or weakened after repeated air-filter service. This six-piece kit restores the applicable mounting and retention points while adding a clean chrome-and-silver appearance to the engine compartment.
| Producer | Hawks Motorsports |
|---|---|
| Product type | Air-box hardware and air-lid clip kit |
| Vehicle platform | Fourth-generation GM F-Body |
| Model years | 1998-2002 |
| Engine application | LS1 V8 |
| Mounting bolts | Four titanium bolts with silver finish |
| Air-lid clips | Two chrome fastener clips |
| Clip reference | Replaces GM 25043286 |
| Total quantity | Six pieces |
| Application | Factory-style air-box and air-lid assemblies |
| Finish | Chrome and silver |
| Condition | New replacement and reproduction components |
- Four titanium lower air-box mounting bolts
- Silver bolt finish
- Two chrome air-lid fastener clips
- Six total pieces
- Components for one compatible air-box assembly
- Replacement components for the original mounting and lid-retention locations
The lower air box, air-filter element, air lid, intake duct, mass-airflow sensor and other intake-system components are not included.
Six-Piece Kit Configuration
| Component | Quantity | Finish |
|---|---|---|
| Lower air-box mounting bolts | Four | Titanium silver |
| Air-lid fastener clips | Two | Chrome |
| Total | Six | Chrome/Silver combination |
The four titanium silver bolts and two chrome clips provide a coordinated, clean finish for the factory-style intake assembly. This version is suited to restored or customized engine compartments where brighter hardware is preferred over an original-style or blacked-out finish.
The titanium mounting bolts provide a lightweight, corrosion-resistant replacement for deteriorated original hardware. The chrome clips complete the front air-lid retention points and replace the applicable original clips associated with GM number 25043286.
| Years | Make | Model | Required configuration |
|---|---|---|---|
| 1998-2002 | Chevrolet | Camaro Z28 | Factory-style LS1 V8 air box |
| 1998-2002 | Chevrolet | Camaro SS | Compatible LS1 V8 air box |
| 1998-2002 | Pontiac | Firebird Formula | Factory-style LS1 V8 air box |
| 1998-2002 | Pontiac | Trans Am | Factory-style LS1 V8 air box |
| 1998-2002 | Pontiac | Trans Am WS6 | Compatible Ram Air air box |
- Intended for compatible 1998-2002 LS1-powered Camaro and Firebird models
- Designed for factory-style lower air-box and air-lid assemblies
- Includes four titanium silver air-box mounting bolts
- Includes two chrome air-lid fastener clips
- Contains six total pieces
- Air-lid clips replace GM part number 25043286
- Fits compatible standard LS1 and Ram Air-equipped vehicles
- Does not apply to V6 air-intake assemblies
- Aftermarket air lids may use different retention components
- Inspect the plastic air-box mounting locations before installation
Fitment should be determined by the installed air-box assembly rather than the vehicle’s model year alone.
Air-Box and Air-Lid Verification
Before ordering, verify that the vehicle retains the compatible factory-style LS1 air box. Confirm that the lower housing uses four mounting bolts and that the air lid has two front spring-clip retention points.
Both clips should engage firmly without excessive force. Resistance or misalignment may indicate an incorrectly positioned filter, distorted lid or incompatible aftermarket component.
Installation Information
Before installation:
- Park the vehicle on a level surface
- Switch off the ignition
- Allow the engine compartment to cool
- Confirm that four bolts and two clips are present
- Compare the new components with the original hardware
- Inspect the lower air-box housing for cracks or damaged mounting points
- Verify that the air filter is positioned correctly
- Align the air lid with the lower housing
- Start each air-box bolt by hand
- Tighten the bolts evenly without distorting the plastic housing
- Install one clip at each applicable front air-lid retention point
- Confirm that both clips engage securely
- Check that the lid sits evenly around the air-filter perimeter
Do not use the mounting bolts to pull a misaligned air-box housing into position. The housing should rest naturally against its mounting locations before the bolts are tightened.
What is included?
The kit contains four titanium silver lower air-box mounting bolts and two chrome air-lid fastener clips.
How many pieces are included?
Six pieces are included in total.
What finish does the kit have?
The titanium air-box mounting bolts have a silver finish, and the two air-lid fastener clips have a chrome finish.
What vehicles does this kit fit?
It is designed for compatible 1998-2002 Chevrolet Camaro and Pontiac Firebird models equipped with an LS1 V8 and factory-style air-box assembly.
Does it fit a Camaro Z28?
Yes. It fits compatible 1998-2002 Camaro Z28 models retaining the factory-style LS1 air box and lid.
Does it fit a Camaro SS?
Yes, when the Camaro SS uses the compatible LS1 air-box and air-lid configuration.
Does it fit a Firebird Formula?
Yes. It fits compatible 1998-2002 Firebird Formula LS1 air-box assemblies.
Does it fit a Pontiac Trans Am?
Yes. It is intended for compatible 1998-2002 Pontiac Trans Am models.
Does it fit a Trans Am WS6?
Yes. It is intended for compatible WS6 and Ram Air-equipped factory air-box assemblies.
Does it fit a V6 Camaro or Firebird?
No. This kit is intended for the compatible LS1 V8 air-intake assembly.
Will it fit an aftermarket air lid?
Not necessarily. Aftermarket lids may use different clips, mounting points or retention methods. Compare the installed lid with the product photographs before ordering.
Are the mounting bolts titanium?
Yes. The kit includes four titanium air-box mounting bolts with a silver finish.
What GM number do the air-lid clips replace?
The two chrome air-lid fastener clips replace original GM part number 25043286.
Is the air box included?
No. This listing is for the mounting bolts and air-lid clips.
Is the air lid included?
No. The air lid must be reused or purchased separately.
Is an air filter included?
No. An air-filter element is not included.
Does the kit contain enough components for one vehicle?
Yes. It provides four bolts and two clips for one compatible factory-style air-box assembly.
Can these bolts repair damaged air-box mounting points?
No. Cracked or damaged plastic mounting locations must be repaired or replaced before the components are installed.
