Product Description:
Hawks Motorsports offers our clients this 1970-1981 Camaro Lower Dash Panel Trim Assembly with Radio, Glove Box and Air Vent Openings OER - 6264754 for restoring the lower dashboard area on second generation Camaro models.
IMPORTANT NOTES:
* 1970-1971 Models did not have the opening for the fasten seat belt warming lamp. (Unit mounts fine but that is different on early models.
* 1976-1981 Camaro Factory radios had a slightly different radio know measurement. If running a 76-81 GM radio some trimming will be required so the radio posts will fit properly. 70-76 spacing was 6.25 inch 76-81 models radio post spacing was 5.75 inches.
This OER reproduction lower dash panel trim assembly houses the in-dash radio opening, glove box section, and air vent assembly area. It is manufactured from injection-molded ABS and designed to replicate the original lower dash panel in appearance, design, and fitment for factory-style interior restoration.
This panel is commonly needed when the original lower dash trim is cracked, brittle, warped, cut for an aftermarket radio, broken around the glove box area, damaged near the vent opening, missing mounting points, or simply too tired to survive another dashboard rebuild. It is a key lower dash component because it ties together the radio area, glove box section, and passenger-side vent area in one visible assembly.
This is a strong restoration part for Camaro owners rebuilding the lower dash, replacing damaged radio trim, correcting glove box area damage, or finishing an interior restoration on Base, Rally Sport, LT, Berlinetta, Sport Coupe, SS, or Z28 models.
Features:
- Fits 1970-1981 Chevrolet Camaro applications with fitment notes below
- OER reproduction lower dash panel trim assembly
- Part number 6264754
- Houses the in-dash radio opening
- Houses the glove box section
- Houses the air vent assembly area
- Injection-molded ABS construction
- Factory-style grain and original-style appearance
- Designed to replicate the original lower dash panel assembly
- Useful for replacing cracked, cut, broken, brittle, warped, or missing lower dash trim
- Good replacement when the radio area, glove box section, or vent area is damaged
- Helps restore the factory-style second generation Camaro dashboard appearance
- Sold individually
Includes:
- One lower dash panel trim assembly
- Dash panel only unless otherwise specified
- Glove box liner, glove box door, glove box lock, latch, hinges, radio, radio brackets, ash tray, air vent outlet, ducting, HVAC controls, steering column cover, screws, clips, wiring, and installation tools are not included unless specifically stated
Fitment:
- 1970 Chevrolet Camaro
- 1971 Chevrolet Camaro
- 1972 Chevrolet Camaro
- 1973 Chevrolet Camaro
- 1974 Chevrolet Camaro
- 1975 Chevrolet Camaro
- 1976 Chevrolet Camaro
- 1977 Chevrolet Camaro
- 1978 Chevrolet Camaro
- 1979 Chevrolet Camaro
- 1980 Chevrolet Camaro
- 1981 Chevrolet Camaro
- 1970-1981 Chevrolet Camaro Base
- 1970-1981 Chevrolet Camaro Rally Sport / RS where applicable
- 1973-1981 Chevrolet Camaro LT / Berlinetta where applicable
- 1970-1972 Chevrolet Camaro SS
- 1970-1974 Chevrolet Camaro Z28
- 1977-1981 Chevrolet Camaro Z28
Fitment Note:
- This lower dash panel is commonly referenced as a first-design style lower dash panel.
- Exact original application centers around the 1972-1976 first-design radio layout.
- It can be used as a service replacement on 1970-1971 models, but the panel includes the later-style seat belt warning lens area that early original panels did not use.
- Later 1976-1981 models may require slight modification to the radio holes depending on the vehicle and radio opening style.
- Original 1970-1972 panels used a radio-hole spacing of approximately 6.25 inches and did not include the seat belt warning lens.
- 1973-1976 first-design panels used approximately 6.25 inch radio-hole spacing with the seat belt warning lens.
- Later second-design panels used approximately 5.75 inch radio-hole spacing.
- Verify radio opening, glove box area, air vent housing, dash style, trim level, and existing panel design before ordering.
- Test fit before painting, trimming, modifying, or final installation.
